Out-of-Reach Taglines
Vertically hanging taglines may settle beyond comfortable reach and tempt personnel to move closer to the suspended load.
A telescopic hands-free safety tool engineered to retrieve vertically hanging taglines and gently guide suspended loads while helping workers maintain distance from pinch points, struck-by hazards and the fall zone.

Hanging taglines, moving loads and tight landing areas can expose personnel to suspended-load movement, pinch points and the load shadow.
Vertically hanging taglines may settle beyond comfortable reach and tempt personnel to move closer to the suspended load.
Entering the fall zone or load shadow places the body where uncontrolled load movement can cause serious harm.
Direct hand contact during positioning can expose fingers, hands and feet to trapping or impact.
Tight work areas make small directional corrections difficult without a purpose-built remote guidance tool.
The modified telescopic pole combines two task-specific ends with adjustable reach for hands-free tagline retrieval and controlled load guidance.
Captures and retrieves vertically hanging taglines from a safer working position.
Provides a cushioned contact point for gently pushing, guiding or redirecting loads.
Adjusts from approximately 4 ft retracted to 7 ft fully extended.
The fully retracted position is recommended when pushing or guiding heavier loads.
Modified aluminium pole with heavy-duty fibreglass and a square aluminium internal extension.
Designed to form part of task planning, pre-use inspection and hands-free lifting controls.
Retrieve the line and guide the load without changing tools, while selecting the telescopic length appropriate to the task.
Use the hook end to capture a hanging tagline while remaining outside the immediate load hazard area.
Use the rubber buffer to apply controlled directional contact, especially in tight or congested spaces.
Retract for rigidity or extend for reach, recognising that rigidity decreases as extension increases.
The PSC-TRT is one telescopic tool with selectable working length. Apply only the controlled force appropriate to its extension.
Approximately 1.2 m. Recommended for pushing or guiding heavier loads because the pole is most rigid.
Useful where intermediate reach is needed; excess force may cause the telescopic section to move inward.
Approximately 2.1 m hook-end retrieval reach. Use controlled pressure because rigidity is reduced.
The specifications below reflect the PSC Tagline Retriever Tool datasheet and product information.
| Product | PSC Tagline Retriever Tool |
|---|---|
| Part Number | PSC-TRT |
| Primary Functions | Tagline retrieval, tangle control, remote load direction and hands-free load guidance |
| Fully Extended Length | Approximately 2.1 m / 7 ft at the hook end |
| Fully Retracted Length | Approximately 1.2 m / 4 ft |
| Pole Type | Modified telescopic boat-hook style pole |
| Construction | Aluminium telescopic pole with heavy-duty fibreglass and square aluminium internal extension |
| Retrieval End | Hook for vertically hanging taglines |
| Guidance End | Rubber buffer for gently pushing and guiding suspended loads |
| Recommended Pushing Position | Fully retracted for heavier loads and maximum rigidity |
| Extended Behaviour | Reduced rigidity; excess force may telescope the pole inward |
| Pre-Use Inspection | Inspect pole, hook and rubber buffer before every use |

Use the PSC-TRT where personnel need to retrieve a line or make a gentle directional correction without placing hands directly on the load.
Hook and recover a vertically hanging tagline without moving unnecessarily toward the suspended load.
Reach, separate or redirect accessible line sections as part of a planned lifting operation.
Use the rubber buffer for gentle directional input while remaining clear of pinch and impact points.
Guide suspended loads where restricted space makes direct manual contact especially hazardous.
The PSC Tagline Retriever Tool supports planned tagline retrieval and gentle suspended-load guidance while helping personnel maintain a safer working position away from pinch points and the load shadow.
Use the hook end to reach a vertically hanging tagline without unnecessarily closing the distance to the load.
Use the rubber-buffer end for gentle directional input where direct hand contact should be avoided.
Select only the extension needed for the task and keep the operator outside the fall zone and load shadow.
The tool supports safer work positioning; it does not make the fall zone or load shadow safe to enter.
Keep the entire body outside the load shadow and never stand beneath or immediately beside a suspended load.
Check the telescopic pole, hook and rubber buffer for damage, looseness or wear before every task.
Use the pole fully retracted when pushing or guiding heavier loads to maximise rigidity.
Use controlled pressure at partial or full extension; excessive force may drive the telescopic section inward.
Use the hook for taglines and the rubber buffer for gentle contact with the suspended load.
Include the tool, operator position and intended method in the lift plan and task risk assessment.
The PSC-TRT becomes less rigid as it extends. Do not apply uncontrolled or excessive force, and never use the tool as permission to enter the fall zone.
Approach only from an approved position, select the necessary extension, engage a hanging tagline with the hook or contact the load gently with the rubber buffer, and maintain the planned standoff throughout the task.
Selection, operation and safety information for the PSC Tagline Retriever Tool.
Review the product details and contact PSC for quotation, application guidance or the approved PSC Tagline Retriever Tool datasheet.
Review the official PSC product page or contact the team for the current datasheet and support selecting the operating configuration for your lifting task.