Pinch & Crush Exposure
Hands wrapped around cylindrical loads can be trapped if the object rolls, shifts or contacts nearby equipment and structures.
PSC Handle-Tech™ is a quick-latch manual carrying tool designed to grip compatible pipes, hoses, rolls and cylindrical components. The operator holds the ergonomic handle instead of the load surface, supporting a more upright posture and helping keep hands away from common pinch, crush and contamination zones.

Large pipes and hoses can be difficult to grip, especially when wet, muddy, oily, contaminated or positioned near the ground. Conventional handling can combine awkward posture with direct hand exposure.
Hands wrapped around cylindrical loads can be trapped if the object rolls, shifts or contacts nearby equipment and structures.
Lifting a hose from ground level or dragging it across a site can create awkward posture, fatigue and loss of balance.
Wet, muddy or oily hoses are difficult to control by direct grip, particularly across uneven or slippery terrain.
Process, waste, fuel and chemical hoses may present contamination or leakage-related exposure at the outer surface.
The curved jaw closes around the object, the latch secures the grip and the operator lifts from the upper handle. The selected jaw range must match the actual outside diameter.
Designed to attach with a quick closing action without separate installation tools or routine diameter adjustment.
The hand remains on the carrying handle instead of wrapping around the hose, pipe or roll surface.
Supports suitcase-style carrying and can reduce the need to hug or continuously drag large hoses.
The tool remains engaged during the carry and is released by the operator after the object is safely supported.
The integrated handle is intended for controlled operation with suitable work gloves.
Standard sizes cover actual outside diameters from 3 inches through 6.75 inches, with gaps between ranges.
Handle-Tech converts a difficult-to-grip cylindrical surface into a defined carrying point while preserving operator control over engagement and release.
Close the quick latch and positively confirm engagement before applying any lifting force.
Use the upper handle to raise and reposition a compatible object within the approved manual-handling plan.
Fully support and stabilize the object before operating the release mechanism and removing the tool.
Measure the object before selection. Nominal pipe or hose size may differ from its actual outside diameter.
For compatible smaller hoses, tubes, pipes, drilling-mud lines and process hoses.
General-purpose variant for compatible industrial pipes and hoses.
For compatible large-bore hoses, rolls, conveyor idlers and cylindrical components.
Contact PSC with the measured outside diameter, object type, surface and operating conditions.
The stated 1,100+ lb figure is a load-test statement from the supplied datasheet; it is not presented as a certified working load limit or permissible manual carry weight.
| Product | PSC Handle-Tech™ Pipe & Hose Lifter |
|---|---|
| Series | PSC-HTL Series |
| Part Numbers | PSC-HTL-002, PSC-HTL-004, PSC-HTL-006 |
| Standard Diameter Ranges | 3–3.75”, 4–4.75”, 6–6.75” actual outside diameter |
| Other Sizes | Available on request |
| Latch Mechanism | Quick-latch: click, grip, lift, move |
| Load Test Statement | Tested to over 1,100 lb according to supplied datasheet—not a declared WLL |
| Hand Contact Concept | Operator holds the handle instead of the load surface |
| Handle | Ergonomic; intended for gloved, one-handed handle operation |
| Electrical | Insulating construction claimed; no voltage or test standard supplied |
| Temperature | Temperature resistance claimed; no operating range supplied |
| Intended Environments | Industrial, oil and gas, offshore, process, utility, food and agriculture |
Use only on compatible objects within the selected jaw range and an approved manual-handling procedure.
Drilling-mud suction hoses, water-truck hoses, frack-pond transfer lines and compatible field hoses.
Compatible tanker, fuel, chemical, gas and process hoses subject to material and environmental approval.
Vacuum-truck hoses, bio-waste pump-out hoses, wastewater and water-treatment lines.
Compatible pinch rolls, TC rolls, work rolls, conveyor idlers, tube bundles and cylindrical components.

Handle-Tech is a manual handling aid. Suitability depends on correct sizing, positive latch engagement, object condition, balance, personnel and the approved work method.
Select by measured outside diameter rather than nominal pipe or hose designation.
Check the jaw, latch, handle, pivots and fasteners for wear, damage, deformation or looseness.
Do not lift until the quick latch is completely engaged and the jaw is correctly seated.
Keep hands away from the closing jaw, latch, adjacent structures and load-contact zones.
Plan personnel, lifting points, footing and travel path for the object's weight, length and flexibility.
Set the object down securely and remove load from the tool before operating the release.
The 1,100+ lb test statement does not authorize a worker to carry that weight. Follow site manual-handling limits and obtain PSC confirmation for the intended object and operating environment.
Product-selection, application and safe-use guidance for the PSC Handle-Tech™ Pipe & Hose Lifter.
Send PSC the actual outside diameter, object type, surface material, weight, length, contents and operating conditions for application support.
Download the PSC Handle-Tech™ datasheet or contact PSC to confirm the correct variant and suitability for the intended pipe, hose or cylindrical component.