PSC-FS Series · Impact and Pinch Point Safety Tool

PSC FingerSaver™

Hold the Workpiece. Keep the Hand Out of the Strike Zone.

PSC FingerSaver™ is a lightweight hands-off safety tool that holds chisels, punches, nuts, bolts and fittings while keeping the operator's fingers clear of hammer impacts, flogging spanners and pinch points.

Request a Quote View Product Details
PSC FingerSaver hand and finger safety tool
3 sizes295 mm · 350 mm · 850 mm
295mm Compact model
350mm Standard model
850mm Long model
3task-specific sizes
The Challenge

The hand holding the workpiece is often directly in the line of fire.

Holding a chisel, punch, bolt or fitting during hammering and wrench work exposes fingers to missed strikes, glancing blows, vibration and trapping points.

01

Missed Hammer Strikes

A missed or deflected blow can land directly on fingers holding the workpiece.

02

Flogging Spanner Impact

Hands positioned beside a struck spanner remain exposed throughout tightening and breakout work.

03

Pinch Points

Impact wrenches and moving components create trapping hazards at the tool and fastener interface.

04

Fatigue and Poor Access

Vibration, low lighting and awkward access increase the chance of grip loss and inaccurate strikes.

The Solution

A simple interface between the hand and the hazard.

The operator grips the FingerSaver while the tool holds the workpiece. Its length creates separation, and its rubber handle supports controlled use during repeated-impact work.

01

Hands-Off Workpiece Control

Holds the chisel, punch, bolt or fitting so fingers do not need to enter the impact zone.

02

Vibration-Absorbing Grip

The rubber grip reduces vibration reaching the hand during sustained striking work.

03

Non-Slip Handling

Supports secure, controlled handling in wet, oily or fatigue-prone conditions.

04

Lightweight Construction

Adds minimal handling fatigue while maintaining the required standoff.

05

Immediately Usable

No assembly or setup is required. Select the correct size, inspect it and follow the approved task procedure and operator instruction before use.

06

Three Practical Sizes

Choose Compact, Standard or Long according to access and separation requirements.

Purpose-Built Hand Separation

Hold the work securely. Move the hand away.

FingerSaver preserves the familiar work method while changing where the supporting hand is positioned. The workpiece remains controlled and the hand remains outside the immediate strike or pinch zone.

Controlled Workpiece Support

Grip the workpiece with the FingerSaver instead of stabilising it with exposed fingers.

Impact-Zone Separation

The tool length creates a defined standoff between the hand and the striking point.

Task-Matched Reach

Select 295 mm for confined access, 350 mm for standard work or 850 mm for maximum separation.

Available Variants

Three sizes for different access conditions.

Choose the model according to the workpiece, available space, task geometry and required hand-to-hazard separation.

295 mmPSC-FS-295

Compact model for punches, chisels, confined access and easy-reach work.

350 mmPSC-FS-350

Best-selling Standard model for flogging spanners, nuts and bolts.

850 mmPSC-FS-850

Long model for maximum standoff and suitable solo or teamwork operations.

Technical Overview

Three lengths. One hands-off purpose.

The PSC-FS range provides task-matched standoff with lightweight handling and a vibration-absorbing rubber grip.

ProductPSC FingerSaver™ Hand and Finger Safety Tool
Part NumbersPSC-FS-295 / PSC-FS-350 / PSC-FS-850
Compact295 mm - punch, chisel and confined-access work
Standard350 mm - flogging spanner, nut and bolt work
Long850 mm - maximum standoff and teamwork
GripVibration-absorbing non-slip rubber grip
WeightLightweight
OperationNo setup required
IndustriesOil and gas, offshore, industrial and construction
Critical LimitationNot rated for lifting or load-bearing use
PSC FingerSaver holding a spanner during industrial fastener work
Applications

Built for work involving impact and pinch hazards.

Use FingerSaver wherever a hand would otherwise be required to hold a workpiece beside a striking, fastening or moving interface.

Application 01

Flogging Spanner Work

Hold nuts, bolts and fittings while keeping fingers clear of the hammer impact path.

Application 02

Chisels and Punches

Position a chisel or punch without wrapping the supporting hand around the striking point.

Application 03

Impact Wrench Tasks

Evaluate suitable component-holding tasks around impact wrenches. Keep clear of moving parts and follow the approved risk assessment and operating procedure.

Application 04

Industrial Maintenance

Support fastener, flange, assembly and shutdown work in restricted-access areas.

The Hands-Off Approach

Control the workpiece. Keep fingers clear.

Correct use begins with a task risk assessment, suitable PPE, correct tool size and a controlled striking method.

01 — Assess the Task

Identify the impact zone, pinch points, access limits and correct FingerSaver size before starting.

02 — Wear Eye Protection

Use safety goggles during striking work to address the secondary hazard from debris.

03 — Match the Hammer

Choose a suitable hammer weight for a natural, controlled swing without overswinging.

04 — Maintain the Standoff

Keep the supporting hand on the rubber grip and never reach toward the striking point.

05 — Inspect Before Use

Remove a damaged or excessively worn FingerSaver from service.

06 — Do Not Modify

Do not repair, alter or replace damaged components; consult PSC or authorised service personnel.

!

Not a Lifting Device

The PSC FingerSaver™ is not rated for load bearing or lifting under any circumstances.

FAQs

Frequently Asked Questions

Key selection, application and safe-use questions about the PSC FingerSaver™ range.

What is the PSC FingerSaver?
It is a lightweight tool that holds a workpiece while keeping the operator's hand clear of hammer impacts and pinch points.
Which sizes are available?
Compact 295 mm, Standard 350 mm and Long 850 mm.
Which model is used for flogging spanners?
The 350 mm PSC-FS-350 Standard is the best-selling model for flogging spanner and nut-and-bolt work.
Which model suits chisels and punches?
The 295 mm PSC-FS-295 Compact suits punches, chisels and confined-access tasks.
When is the 850 mm model appropriate?
Use PSC-FS-850 where maximum standoff or suitable two-person operation is required.
Does it require setup?
No setup is required, but it must be inspected and selected according to the task risk assessment.
Can it be used for lifting?
No. It is not rated for lifting or load-bearing use.
Can a damaged FingerSaver be repaired on site?
No. Do not repair or modify it; consult PSC or authorised service personnel.
PSC FingerSaver™ Resources

Get the product information you need.

Access technical information or contact PSC for help selecting the correct FingerSaver size for your impact-zone and pinch-point task.

Compact, Standard and Long variants
Vibration-absorbing non-slip rubber grip
Lightweight and immediately usable
Impact-zone and pinch-point separation
Product Resources

Datasheet or direct quotation request.

Download the PSC FingerSaver™ datasheet for sizes, applications, specifications and safe-use guidance, or contact PSC for selection support.

sales@pschandsafety.com
www.pschandsfree.com