Pipe-to-Structure Crush Points
Hands wrapped around the pipe can be trapped if the load moves toward walls, racks, equipment or nearby structures.
PSC EzyLIFT™ is an ergonomic manual pipe carrying tool designed to reduce direct hand-to-pipe contact, support a neutral wrist position and help keep fingers away from sharp edges and common pipe-handling pinch and crush zones.

During a two-person carry, a stumble, uneven surface, coordination loss or sudden pipe shift can move a worker's hand toward a wall, floor, rack, structure or sharp pipe edge.
Hands wrapped around the pipe can be trapped if the load moves toward walls, racks, equipment or nearby structures.
Direct contact with unfinished, burred or damaged pipe ends can expose fingers and palms to cuts and lacerations.
Gripping a cylindrical object can place the wrist in an awkward position and make control dependent on sustained hand strength.
If one worker slips or changes pace, load movement can transfer immediately through the pipe to the other worker's hands.
The operator grips the integrated handle while the shaped engagement arm interfaces with the open pipe end. This changes the handling method from hand-to-pipe contact to hand-to-tool-to-pipe control.
The hand remains on the tool handle rather than wrapping around or beneath the pipe.
The shaped handle is designed to support a more natural wrist position during assessed manual carrying tasks.
The engagement geometry is designed so that contact pressure increases as lifting force is applied.
A simple one-piece form provides an enclosed handle and pipe-engagement arm without powered or complex moving parts.
One EzyLIFT is used at each open end so both workers receive the intended separation benefit.
The tool can be visually checked for cracks, deformation, damage and correct engagement before use.
EzyLIFT is designed around the way an open-ended pipe is manually carried. Its handle and engagement profile form a mechanical interface between the worker and the pipe.
Provides a dedicated carrying grip so the operator does not need to grasp the pipe circumference or edge directly.
The lower arm must be fully inserted into a compatible open pipe end before the lift begins.
The profile is intended to seat against the pipe wall as lifting force is applied, supporting controlled manual carrying.
PSC EzyLIFT™ is identified by part number PSC-EZL. The operating method uses one tool at each accessible open pipe end, with one worker controlling each side of the carry.
Standard EzyLIFT manual pipe lifting and carrying tool.
The intended configuration requires one EzyLIFT at each end of the pipe.
The engagement arm must fit fully inside an accessible and compatible pipe end.
Confirm pipe diameter, wall thickness, end condition, pipe weight and suitability with PSC before use.
Only specifications stated in the supplied EzyLIFT datasheet are shown below. Capacity, dimensions and compatibility limits must be confirmed by PSC for the intended task.
| Product | PSC EzyLIFT™ Pipe Lifting Tool |
|---|---|
| Part Number | PSC-EZL |
| Tool Type | Manual pipe lifting / carrying tool |
| Operating Arrangement | Two tools; one worker at each open pipe end |
| Hand Contact Concept | Operator holds the tool rather than the pipe |
| Grip Behaviour | Designed to increase engagement pressure under higher lifting force |
| Wrist Position | Neutral by design |
| Material | Heavy-duty cast steel, according to supplied datasheet |
| Finish | Black powder coat, according to supplied datasheet |
| Intended Conditions | Gloved and wet-use conditions, subject to task assessment and inspection |
| Industries | Fabrication, oil and gas, offshore, construction and steel |
| Important Limitation | Manual carrying only; not for crane, hoist or overhead lifting |

EzyLIFT supports manual pipe carrying where open pipe ends are accessible and mechanical lifting is impractical or unnecessary.
Carry and reposition compatible pipe sections between cutting, fitting, welding and inspection stations.
Support assessed site, trench-side and installation-related movement of manageable pipe sections.
Move compatible pipe during maintenance, shutdown and deck activities where manual handling is authorized.
Assist production-line and workshop movement of compatible open-ended pipe sections.
The EzyLIFT is a hand-operated carrying aid. It is not a rated crane attachment, hoisting clamp or overhead lifting device.
Use one EzyLIFT at each end so neither worker needs to hold the pipe directly.
Do not begin the lift unless each engagement arm is fully inserted and correctly seated.
Remove the tool from service if cracks, deformation, damage or an incorrect fit is found.
Use task-appropriate gloves and all PPE required by the worksite risk assessment.
Pipe weight and team-lifting limits remain governed by company policy and the task assessment.
Do not drill, thin, hammer, widen or otherwise alter the engagement profile.
Never attach hooks, chains, cables or slings. Do not use the EzyLIFT as a beam clamp, rigging accessory, pry tool or hammer.
Key product, compatibility and safe-use questions about the PSC EzyLIFT™.
Contact PSC with the pipe diameter, wall thickness, end configuration, length, weight, carrying route and operating environment for product-selection support.
Download the PSC EzyLIFT™ datasheet or contact PSC to confirm tool fit and suitability for the intended manual pipe-handling task.