Missed Hammer Strikes
A missed or deflected blow can land directly on fingers holding the workpiece.
PSC Chisel & Punch Holder securely grips chisels and punches up to 1 inch in diameter, allowing the operator to maintain control from an ergonomic handle instead of holding the struck tool directly.
Direct chisel and punch holding exposes the supporting hand to missed blows, tool deflection, sparks, sharp edges and the cumulative effects of repeated impact vibration.
A missed or deflected blow can land directly on fingers holding the workpiece.
A chisel that slips or shifts can redirect both the tool and the hammer toward the hand.
Metalworking and concrete chiselling can expose nearby hands to sparks, chips and sharp fragments.
Repeated strikes transmit vibration through a directly held chisel, increasing strain and fatigue.
PSC-CPH secures the chisel or punch while the operator controls it through an ergonomic handle. The quick-adjust mechanism supports different tool diameters without placing fingers at the striking end.
Secures the chisel or punch so the operator never needs to grip the struck tool directly.
Tool-free adjustment at the base supports fast resizing for different tool diameters.
Accommodates suitable chisels and punches up to 25 mm in diameter.
Helps separate the hand from sparks produced during metalworking and concrete chiselling.
Reduces impact energy transmitted to the operator during sustained striking work.
High-quality materials resist wear in construction, maintenance and fabrication environments.
The base knob adjusts the gripping mechanism to firmly secure a suitable chisel or punch before striking. Correct adjustment preserves positioning and hand separation.
Place a suitable chisel or punch into the gripping end before approaching the work face.
Adjust until the tool is firmly secured; a loose fit reduces both control and protection.
Maintain the designed standoff and never move the supporting hand onto the chisel during striking.
Correct setup ensures the holder, not the hand, remains the interface with the chisel or punch during every strike.
Place a compatible chisel or punch into the holder's gripping end.
Tighten the base knob until the tool is firmly held without looseness.
Hold the ergonomic handle and keep fingers clear throughout striking.
PSC-CPH combines a quick-adjust gripping mechanism with a spark-resistant, vibration-absorbing ergonomic handle.
| Product | PSC Chisel & Punch Holder |
|---|---|
| Part Number | PSC-CPH |
| Chisel Capacity | Up to 1 inch (25 mm) diameter |
| Adjustment | Quick-adjust knob at base |
| Spark Resistance | Yes - spark-resistant handle |
| Vibration Control | Vibration-absorbing handle design |
| Hand Contact | Operator grips the holder handle, not the struck tool |
| Ergonomics | Fatigue-reducing grip |
| Industries | Construction, metalwork, automotive, woodworking and maintenance |
| Critical Limitation | Not rated for lifting or load-bearing use |
Use PSC-CPH wherever a compatible chisel or punch would otherwise need to be held by hand during striking.
Concrete breaking, channelling, masonry punch work, setting fixings and surface preparation.
Punch marking, pin driving, rivet setting and controlled positioning on fabricated components.
Seized fastener and gasket work, mortising, paring and joint-cutting operations.
Chisel and punch work on plant, machinery, equipment and pipework during maintenance or shutdowns.
Correct use requires a compatible tool diameter, firm adjustment, suitable PPE, controlled striking and consistent use of the designated handle. Follow approved working procedures and keep hands and bystanders clear of the strike path.
Use only chisels and punches within the stated 1-inch or 25 mm capacity.
Adjust the base knob until the tool is secure. Never strike a loosely held tool.
Never grip the chisel or punch directly, even briefly, during the striking operation.
Use suitable protection against sparks, chips and debris produced during striking.
Check the jaw, adjustment knob and handle. Remove the holder if wear or looseness is detected.
Use an appropriate hammer and maintain stable posture, access and tool alignment.
PSC-CPH is not rated for load bearing or lifting under any circumstances.
Key capacity, adjustment, application and safe-use questions about PSC-CPH.
Access technical information or contact PSC for help applying the Chisel & Punch Holder to your striking-tool operation.
Request the PSC Chisel & Punch Holder datasheet for capacity, applications, specifications and safe-use guidance, or contact PSC for support.